ECU REMAP

From $1,950.00
Product Code: #PATROL Y61 3.0L | ECU REMAP & ACTUATOR
Install Time: 1 Day
Model Compatibility: Patrol 2007-2016 Y61 3.0L (ZD30)

Share:

STANDARD
DYNO CHIPTUNING
DIFFERENCE
POWER
118kW
158hp
150kW
201hp
+32kW
+43hp
TORQUE
380Nm
280ft-lb
530Nm
391ft-lb
+150Nm
111ft-lb
POWER
STANDARD 118 KW
158 hp
DYNO CHIPTUNING 150 KW
201 hp
DIFFERENCE +32 KW
43 hp
TORQUE
380 Nm
280 ft-lb
530 Nm
391 ft-lb
+150 Nm
111 ft-lb

NISSAN PATROL Y61 ZD30 | ECU REMAP & ACTUATOR

Nissan Patrol Y61 3.0L | ECU Remap & Turbosmart Wastegate Actuator

Enhance your Nissan Patrol Y61 3.0L with our CRD-Flash ECU Remap and Turbosmart Wastegate Actuator, delivering cutting-edge performance optimization. Our state-of-the-art tuning process recalibrates the factory Engine Control Unit (ECU) to boost power, torque, and fuel efficiency while maintaining manufacturer safety protocols. Paired with the precision-engineered Turbosmart Wastegate Actuator, this upgrade optimizes boost control for improved turbo response and performance consistency.

Benefits:
•    Power & Torque Gains: Expect real-world increases of approximately 20% more power and 20% more torque, enhancing drivability without compromising reliability.
•    Fuel Economy: Potential improvement of up to *10% in fuel efficiency.
•    Precision Tuning: We fine-tune torque management, throttle mapping, boost pressure, fuel pressure, injector timing, and more, leveraging the ECU’s full capabilities—unlike basic chips or modules.
•    Turbosmart Wastegate Actuator: Enhances turbo performance by precisely regulating boost pressure, ensuring optimal power delivery and turbo longevity.
•    Safety & Reliability: Retains all factory safety features, ensuring no degradation to vehicle reliability or drivability.

Process: 
The tuning and installation process is completed in approximately one day at Horsepower Factory:

•    Baseline Dyno Run: The vehicle is tested on our All-Wheel Dyno to establish initial performance metrics.
•    ECU Remapping: Using advanced ECU reading and writing hardware, our specialist tuners adjust critical parameters, monitored via dyno screens, ECU logging devices, and EGT sensors.
•    Turbosmart Wastegate Actuator Installation: The actuator is professionally installed to optimize boost control, seamlessly integrating with the ECU remap.
•    Final Dyno Run: Post-tuning, the vehicle is retested to confirm performance gains.
•    Customer Handover: You receive a dyno graph comparing baseline and final runs, showcasing improvements in power and torque.

Experience unmatched performance with the perfect synergy of CRD-Flash tuning and Turbosmart technology, backed by Horsepower Factory’s expertise.

*Results may vary based on vehicle condition and driving habits. Consult Horsepower Factory for details.

Package Includes

1 x Turbosmart wastegate actuator
1 x Custom ECU reprogram
1 x Before and after dyno graph
1 x Labour to fit, tune and test

Key Features

"You never thought a diesel could be this good, much better throttle response, much improved power whilst keeping reliability as the primary focus"

Notes

  • *Power figures listed are estimated kilowatts at the flywheel based on results typically obtained by HPF on HPF’s dynos. Typically these are based of a manual vehicle with standard driveline and standard wheels and tyres. Actual power can vary based on each specific vehicle.
  • We advise against increasing the power output substantially on high kilometer engines, if your engine has in excessive of 150,000kms please contact us to discuss options.
  • Whilst every attempt is made to ensure prices listed online are correct, they are subject to change at any time.
  • Additional parts may be required in some cases depending on the condition of the vehicle. Cost of these parts and additional labor required may incur additional cost.
  • Images are for illustration purposes only.

Enquire Here